LG jobs we've documented in Burbank
-
LG refrigerator: compressor running, nothing cooling
- What the customer saw
- The refrigerator was warm, yet its compressor kept running and rattled loudly.
- What we found
- Our gauges read 15 PSI on the low side instead of a vacuum: the pump inside the linear compressor had broken and shed metal through the whole sealed system.
- What we did
- After flushing the system and updating the control board firmware, we brazed in a new LG compressor and filter-drier, then re-brazed a pinhole the nitrogen test turned up. The system held 300 microns and cooled again.
-
LG WM8100HVA under a dryer, stuck on OE
- What the customer saw
- The LG front-loader, installed under a dryer, stopped with water in the drum and an OE code on the display.
- What we found
- The drain pump filter had nothing in it, which left the drain pump itself as the fault.
- What we did
- We rolled the stack out on sliders, opened the washer from the back and then the front, and fitted a new drain pump. The test cycle drained with a dry floor, and the stack went back with room left for the hookups.
Recent jobs in the area


Quick facts
| Service call | $85 — credited toward the repair when you proceed |
|---|---|
| Warranty | 30-day labor · 90 days on parts we supply |
| Credentials | BEAR #A 50636 · EPA Section 608 Universal |
| Hours | Mon–Fri 09:00–19:00 Sat–Sun 10:00–16:00 |
Updated October 2026
Two LG repairs in Burbank
We’ve documented two LG jobs in Burbank: a refrigerator that kept running after it stopped cooling, and a front-loader, stacked under a dryer, that stopped on OE with water in the drum. On the fridge, a gauge reading pointed to the compressor. On the washer, a clean drain filter pointed to the pump.
The refrigerator: running, rattling, not cooling
The LG refrigerator job started with a warm fridge and a compressor that was still running, with a loud rattle you can hear in our video of the job. Our gauges showed 15 PSI on the low side. With the compressor on, an R600a system should show a vacuum there, so this one was running without pumping. The mechanical pump inside it had failed.
When that pump broke, it sent metal particles through the sealed system, so the system had to be cleaned out before a new compressor went in. Acetone and high-pressure nitrogen went through each circuit: the capillary tube, fed through a homemade adapter, plus the condenser coil and the door heater loop. Next, we loaded updated firmware onto the control board with LG’s official programmer so it would match the new compressor, and only then brazed in the new LG compressor along with a new filter-drier.
The vacuum wouldn’t hold at first. Nitrogen pressure and bubble leak detector found why: a bubble kept growing at the compressor access valve, where a joint that had looked fine had a pinhole in the braze. Once that joint was re-brazed, the vacuum held at 300 microns, and with the fridge back on, the low side read -7.1 PSI.
A compressor replacement of this scope typically runs $780–$1,050, parts and labor included, depending on the model and access. If your LG needs a compressor, ask what the quote covers. On this fridge it took a sealed-system flush, a new filter-drier, a firmware update and a nitrogen leak test.
The washer: OE on an LG under a dryer
The stacked washer job was an LG WM8100HVA front-loader installed under a dryer. It had stopped on OE, LG’s drain error, and wouldn’t pump the water out. A clogged drain pump filter, a kinked drain hose or a failed pump can all set that code, and our LG washer OE page sums them up. This filter was clean, which left the pump.
Reaching it took more work than the diagnosis. We put the pair on sliders and pulled the stack out of its alcove to reach the back. With the washer’s top panel off from behind and its front panel removed, we swapped in a new drain pump. The test cycle drained with no leaks, and OE didn’t come back. When we pushed the stack into its alcove again, we left a gap behind it: a drain hose pinched against the wall can set off the same code.
A drain pump replacement like this one typically runs $230–$320, parts and labor included, depending on the model and access.
Before you call about your LG
If it’s the refrigerator, tell us whether you can hear the compressor running and whether both sections are warm, and text us a photo of the model sticker. If the washer shows OE, take a picture of the code before you reset anything. Before you open the drain pump filter, unplug the washer, let hot water cool and drain what’s left through the emergency drain hose, following your model’s manual. A clogged filter can be the whole fix.
We work across Burbank (91501, 91502, 91504, 91505 and 91506) and the rest of Los Angeles: the San Fernando Valley, Hollywood and Mid-City, the Westside, and the beach cities and South Bay. See our Burbank service area, LG appliance repair, refrigerator repair and washer repair pages. We’re CA BEAR registered (#A 50636) and EPA Section 608 Universal certified, and the $85 service call is credited toward the repair if you go ahead. The ranges above include it, and you get the exact price in writing after the diagnosis. Labor carries a 30-day warranty and parts we supply carry 90 days. Call or text (213) 205-2055.
Frequently asked questions
-
My LG fridge is warm, but I can hear the compressor running. Can it still be the compressor?
Yes. The LG we repaired in Burbank ran and rattled without pumping anything: its low side sat at 15 PSI instead of below zero, and the pump inside the linear compressor was broken. A compressor can run and still move no refrigerant, and on this fridge the gauges showed it.
-
What does replacing a failed LG compressor involve?
On the Burbank job it took more than a new compressor. Metal from the broken pump had to come out of the sealed system first, so the circuits got an acetone and nitrogen flush, and a new filter-drier went in with the new LG compressor. Before the compressor went in, we updated the control board firmware with LG's official programmer to match it. A nitrogen test with bubble leak detector then caught a pinhole in the braze at the compressor access valve, and after re-brazing, the vacuum held at 300 microns.
-
My stacked LG washer stopped on OE with water in the drum. Is it the drain pump?
It can be. OE is LG's drain error, and a clogged drain pump filter or a kinked or blocked drain hose can set it too. On the WM8100HVA we repaired in Burbank, the filter was clean, and a new drain pump cleared the code. Start with the filter and the hose. Unplug the washer, let hot water cool and drain what's left through the emergency drain hose, following your model's manual, before you open the filter.
-
How do you get to the drain pump with a dryer stacked on the washer?
On the Burbank job, the pair went onto sliders and came out of the alcove as one stack, which gave us the back. We lifted off the washer's top panel from behind, removed the front panel, and the pump was within reach. Before the stack went home, a test cycle confirmed it drained, and we left space behind it so the water lines, drain hose, power cords and dryer vent wouldn't get pinched.
-
What does LG repair cost in Burbank?
Our service call is $85, credited toward the repair if you go ahead, and you get the exact price in writing after the diagnosis. From the two Burbank jobs: a compressor replacement like the refrigerator's typically runs $780–$1,050, and a drain pump replacement like the washer's $230–$320, parts and labor included. Labor carries a 30-day warranty and parts we supply carry 90 days.
Book a diagnostic/repair visit
Get your LG looked at in Burbank
Or text a photo so we can bring the right part.