Skip to main content

LG over-the-range microwave in Valley Village: finishing an installation the customer started

The customer had started hanging his new LG over-the-range microwave himself and couldn't finish. We replaced the mounting hardware, prepared the opening to the right size and put the microwave in place.

November 16, 2026 · 4 min read · By Epic Star Service Team

LG over-the-range microwave with ThinQ hung under a wood upper cabinet, its handle still in plastic wrap.
In this guide

Where the install had stopped

A customer in Valley Village started installing his new LG over-the-range microwave with ThinQ himself in October 2026 and couldn’t finish the job.

The photo below shows the kitchen before we hung it. The microwave is on the counter with its handle still wrapped in plastic. The wall plate is already on the wall between the cabinets, and the power cord runs up through a hole in the floor of the upper cabinet, where the outlet is. A level lies on the cabinet floor. LG’s paper upper-cabinet template and the installation guide are on the counter, on newspaper spread out to protect it.

LG microwave on a counter under an open upper cabinet, with the metal wall plate on the wall, the power cord running up through a hole in the cabinet floor, an outlet inside the cabinet and the upper-cabinet template on the counter.

What we did to get it on the wall

We replaced the mounting hardware and prepared the opening to the right size. With those two things done, the microwave went up under the upper cabinet, where it’s installed now.

The photo at the top of this page was taken afterward: the cabinet doors are closed and the microwave hangs under them, the plastic still on its handle.

The sizes that matter for your kitchen are in the installation guide for your model.

What should you check before hanging an over-the-range microwave yourself?

An over-the-range microwave hangs from two points. A metal plate on the wall holds the back, and bolts through the bottom of the upper cabinet hold the top. Both have to line up with the microwave, and the cord has to reach an outlet in the cabinet above. What follows is general guidance; the installation guide for your model has the final word on every dimension.

Start with that guide. It gives the opening width, the clearance above the cooktop and the space the upper cabinet needs. Measure your cabinets and range against those numbers before you buy hardware or drill.

The wall plate goes into studs. Guides ask for at least one screw into a wood stud, with the anchors they specify where there’s no stud. Place the plate where the guide shows and check it with a level before you tighten anything. A crooked or off-center plate can leave the microwave crooked or keep it from lining up with the cabinet bolts.

Drill the upper cabinet from the paper upper-cabinet template. It marks where the top bolts go through and where the power cord goes up. Tape it where the guide says and drill through the marks.

Look inside the upper cabinet for the outlet before the day you hang the microwave. The cord plugs in up there. If there’s no outlet in that cabinet, an electrician has to add one first.

Settle the vent direction early. Depending on the model and your kitchen, the microwave either recirculates air back into the room or exhausts it outside, and changing the blower direction has to happen before it goes on the wall.

You’ll need a helper. One person holds the microwave tilted onto the plate’s tabs while the other feeds the cord through the cabinet and starts the top bolts. The guide lists the weight; don’t try it alone from a step stool.

Stop and get help if the plate can’t reach a stud, the cabinet already has holes in the wrong place, the opening is narrower than the guide allows or the microwave won’t sit flush against the wall.

Microwave repair in Valley Village

Epic Star Appliance Repair and HVAC repairs microwaves, over-the-range units included, across Los Angeles. In Van Nuys we fixed a Wolf built-in microwave that stopped heating. The Valley Village service area page has our other jobs there, such as a Daikin mini-split with a clogged condensate pump. CA BEAR registered (#A 50636). If your microwave stops heating or won’t start, call or text (213) 205-2055 and send a photo of the model sticker.

FAQ

Have you finished an over-the-range microwave install that a customer started?

Yes, on a job in Valley Village in October 2026. The customer had started hanging a new LG over-the-range microwave himself and couldn't finish. We replaced the mounting hardware, prepared the opening to the right size and hung the microwave.

Does the wall plate for an over-the-range microwave have to go into studs?

Installation guides tell you to fasten the plate into wall studs, with at least one screw in a stud and the anchors the guide specifies elsewhere. The plate carries the back of the microwave, so drywall anchors alone aren't enough. Your model's guide shows the screw positions and how the plate lines up with the template.

What is the upper-cabinet template for?

It's the paper sheet you tape to the bottom of the upper cabinet. It marks where to drill the holes for the top mounting bolts and the hole the power cord goes up through to the outlet. If those holes are off, the microwave won't line up with the wall plate.

Where does the power cord of an over-the-range microwave plug in?

The cord runs up through a hole in the bottom of the upper cabinet to an outlet inside that cabinet. On our Valley Village job the outlet was already in the cabinet. If there's no outlet above the range, that's electrical work to sort out before the microwave goes up.

Can one person hang an over-the-range microwave?

Installation guides call for two people. One holds the microwave tilted onto the wall plate's tabs while the other feeds the cord through the cabinet and threads in the top bolts. Check the weight in your model's guide before you lift it.

Do I need to change the vent direction before installing?

Decide that first. An over-the-range microwave can recirculate air back into the kitchen or vent it outside, depending on the model and your kitchen. Changing the blower direction is done before the microwave goes on the wall, and your model's guide shows how.

Got an appliance that needs fixing? We cover LA and the Valley.

Call (213) 205-2055 or text a photo of your appliance.