Skip to main content

Bertazzoni burner won't click in Beverly Hills: spark switch cleaned, no new part

One burner went silent while the other knobs still clicked. The fault sat in a tiny switch on that burner's valve stem, and cleaning its brass contacts brought the click back.

October 28, 2026 · 4 min read · By Epic Star Service Team

Watch: a real Los Angeles repair

Bertazzoni burner won't click in Beverly Hills: spark switch cleaned, no new part
The whole Bertazzoni gas range with its stainless steel front, cooktop grates and control knobs, assembled after the burner repair
In this guide

One burner that wouldn’t click

On this Bertazzoni gas range in Beverly Hills, the left rear burner had gone quiet. Push its knob and nothing happened. The knob next to it clicked, and so did the rest.

Finger pointing at a control knob on a Bertazzoni gas range with a burner that will not click

What makes a gas burner click

On this range, the click you hear comes from the spark module, and the module clicks only when a burner’s spark switch tells it to.

That switch sits on the stem of the burner’s gas valve, inside the range body. It’s a tiny part, but without it that burner gets no click.

Pulling the spark switch off the valve

We took the spark switch off the left rear burner’s valve stem. It came off easily when we pulled on its top part.

Gloved hand holding the red spark switch after removing it from a burner valve stem on a Bertazzoni range

What’s inside a spark switch

Opened up, the switch is two pieces: a cover, and a base that holds brass contacts.

Opened red spark switch with its cover set apart from the base that holds the brass contacts

Push the knob in, and a small lever presses the brass strips together. That connects two wires, and the connection is the signal that tells the spark module to click. Let go of the knob and the switch pops back up. The contacts separate, and the signal stops. Connecting those two wires is the only thing it does.

Close-up of the brass contacts inside the red spark switch base, held between a gloved and a bare finger

The fault on this burner

On this switch, pushing the knob didn’t bring the contacts together. No contact meant no signal to the module, so that burner got no click and no spark.

Same switch, back on the stem

We cleaned the contacts, put the switch back together and set it back on the valve stem. Nothing was replaced. It’s the same switch that came off.

Testing the burner

Then we pushed the knob again and watched the white electrode at the burner. A blue spark showed right at it, and the left rear burner clicked like the others.

Blue spark at the white ceramic electrode of a burner igniter, seen inside the Bertazzoni range body

If a burner on your gas stove won’t click

If you smell gas, don’t push any knobs: leave electrical switches and plugs alone, light nothing, and call the gas company or 911 once you’re outside. Otherwise, push each knob in turn and listen. If one burner stays quiet while the others click, as on this Bertazzoni, note which one for the technician. Here, the missing click came from that burner’s spark switch contacts. If no knob clicks at all, look first at what the burners share. The clicking runs on electricity, so start with the range’s breaker.

Don’t take the range apart to get at the switch. It sits on the gas valve inside the range body, and that’s work for a technician.

Gas ovens have their own ignition parts. In our Chatsworth case, a gas oven that was slow to heat got a new igniter. For other faults on these Italian ranges, see our Bertazzoni repair page.

Gas range repair in Beverly Hills

We repair gas ranges and cooktops in Beverly Hills and across Los Angeles, Bertazzoni included. See our stove and range repair in Beverly Hills page and our stove and range repair service. The $85 service call is credited toward the repair if you go ahead, and repairs carry a 30-day labor warranty and a 90-day warranty on parts we supply. CA BEAR registered (#A 50636). Call (213) 205-2055.

FAQ

Why won't one burner on my gas stove click?

On a range like this Bertazzoni, pushing a burner knob closes a spark switch on that burner's valve, and the switch signals the spark module to click. When one burner stays silent while the others click, that burner's switch is one of the parts to check. On this range in Beverly Hills, its contacts stayed open with the knob pushed in.

What does a spark switch do?

On this Bertazzoni, it connects two wires while the knob is pushed in, and that tells the spark module to click. When you let the knob go, the switch pops back up, a gap opens between its brass contacts and the signal stops. That's the whole job.

Did the spark switch need to be replaced?

No. We cleaned its contacts, put it back together and set it back on the valve stem. The burner clicks like the others now, and no part was replaced.

How did you check the repair?

We pushed the knob and watched the white electrode at the burner. A blue spark showed at it, and the burner clicked like the rest.

Can I fix a gas burner that won't click myself?

Not if you smell gas: then don't test the knobs, don't light anything or touch electrical switches or plugs, and call the gas company or 911 from outside. Without a gas smell, you can push each knob to find the silent burner, and check the range's breaker if none of them click. The spark switch sits on the gas valve inside the range body, so leave removing it to a technician.

Do you repair Bertazzoni ranges in Beverly Hills?

Yes, Bertazzoni and other gas ranges in Beverly Hills and across Los Angeles. The $85 service call is credited toward the repair if you go ahead, and repairs carry a 30-day labor warranty and a 90-day warranty on parts we supply. Call or text (213) 205-2055.

Got an appliance that needs fixing? We cover LA and the Valley.

Call (213) 205-2055 or text a photo of your appliance.