Skip to main content
F8E4 Pro Recommended

KitchenAid Dishwasher F8E4 — Water Detected in the Base

F8E4 appears with an alarm tone, and the dishwasher drains instead of running a cycle.

Updated October 2026

Stylised cutaway illustration of a dishwasher; individual parts are not labelled

What does KitchenAid F8E4 mean?

F8E4 means the dishwasher detected water in its base, where the drip tray and its float switch sit. KitchenAid says the drain sequence then begins and the dishwasher won't run. KitchenAid's own troubleshooting doesn't single out one cause: it has you check the water-supply connection, the float switch and the drip tray after a new install, and look for suds that can push water out of the dishwasher.

What causes KitchenAid F8E4?

  • After a new install, a water-supply connection that isn't sealed (rubber washer not seated in the fitting, or the coupling not tight)
  • After a new install, a float switch that isn't connected
  • Water left standing in the drip tray, which KitchenAid says must be emptied
  • Suds from dish soap or too much detergent, which can push water out of the dishwasher

How to fix KitchenAid F8E4 yourself

  1. 1 On a new install, check the water-supply connection. The rubber washer has to sit properly in the fitting, and the coupling goes on hand-tight first so it doesn't cross-thread. KitchenAid says an extra 1/4 to 1/2 turn with pliers may be needed to seal the gasket.
  2. 2 Check that the float switch is connected. Its connector should be pushed into the housing until the locking tab shows over the back of the connector. KitchenAid also says the power cord shouldn't touch the motor or the lower part of the tub.
  3. 3 Empty the drip tray if it holds water. Press the snap on each side of the tray in toward the center, then pull the tray toward you gently: the float switch wire is still attached, and pulling too far or too hard can damage it.
  4. 4 Clear the code. Press Cancel once to silence the alarm, then again to clear F8E4.
  5. 5 If you see suds, turn the dishwasher off and let them die down. Dish soap, or too much detergent, makes suds that can push water out of the dishwasher. Use only detergent made for automatic dishwashers.
  6. 6 If a professional installed it, shut off its water supply. Press Cancel once to silence the alarm, and leave the power on and the door closed so the drain sequence can run.

Frequently asked questions

  • What does the KitchenAid F8E4 error code mean?

    F8E4 means the dishwasher detected water in its base, where the drip tray and its float switch sit. KitchenAid says the drain sequence then begins and the dishwasher won't run. KitchenAid's own troubleshooting doesn't single out one cause: it has you check the water-supply connection, the float switch and the drip tray after a new install, and look for suds that can push water out of the dishwasher.

  • What causes the KitchenAid F8E4 error?

    After a new install, a water-supply connection that isn't sealed (rubber washer not seated in the fitting, or the coupling not tight); After a new install, a float switch that isn't connected; Water left standing in the drip tray, which KitchenAid says must be emptied; Suds from dish soap or too much detergent, which can push water out of the dishwasher.

  • How can I troubleshoot KitchenAid F8E4 myself?

    On a new install, check the water-supply connection. The rubber washer has to sit properly in the fitting, and the coupling goes on hand-tight first so it doesn't cross-thread. KitchenAid says an extra 1/4 to 1/2 turn with pliers may be needed to seal the gasket. Check that the float switch is connected. Its connector should be pushed into the housing until the locking tab shows over the back of the connector. KitchenAid also says the power cord shouldn't touch the motor or the lower part of the tub. Empty the drip tray if it holds water. Press the snap on each side of the tray in toward the center, then pull the tray toward you gently: the float switch wire is still attached, and pulling too far or too hard can damage it. Clear the code. Press Cancel once to silence the alarm, then again to clear F8E4. If you see suds, turn the dishwasher off and let them die down. Dish soap, or too much detergent, makes suds that can push water out of the dishwasher. Use only detergent made for automatic dishwashers. If a professional installed it, shut off its water supply. Press Cancel once to silence the alarm, and leave the power on and the door closed so the drain sequence can run.

  • When should I call a professional for KitchenAid F8E4?

    If F8E4 keeps coming back after these steps, KitchenAid's next step is a service call. Leave the water supply off until a technician finds where the water in the base is coming from. Call us to trace it.