Skip to main content
nD DIY First

Samsung Washer nD — No Drain Error

The cycle stops early and water stays in the drum.

Updated October 2026

Stylised cutaway illustration of a washing machine; individual parts are not labelled

What does Samsung nD mean?

Samsung's nD is a drain error: the washer could not drain the water. Depending on the model, Samsung shows the same error as 5E, 5C, SE or SC. Samsung says incorrect drain hose installation is the most common reason for drain issues and that service is rarely required.

What causes Samsung nD?

  • Drain hose installed incorrectly: pushed too far into the standpipe, sealed airtight, or outside the height range for your model
  • Kinked, bent or damaged drain hose
  • Clogged debris filter (front-loaders only; top-loaders don't have one)
  • A washer that isn't level
  • A drain pump fault, which needs a technician's diagnosis

How a technician tells the causes apart

  • We check the drain hose installation against the model's installation manual first: depth in the standpipe, an airtight seal, a kink behind the washer and the standpipe height. Samsung names hose installation as the most common reason for drain errors.
  • On front-loaders, the debris filter comes out with a towel and a pan underneath; lint, coins or a sock in it settle the question before anything is opened.
  • The hose is disconnected and checked for a blockage along its length.
  • With the washer unplugged, we check whether the pump impeller turns freely; a jammed or seized impeller points to debris or a worn pump.
  • If the impeller turns freely and the hose is clear, the pump motor and its wiring are tested with the washer unplugged before any pump is ordered.

If testing points to the pump itself, the replacement drain pump has to match your exact model, not just a generic 'Samsung front-load pump.' The model and serial label sits around the front door opening on most front-load Samsung washers; if it's not on the door frame, check the label on the back panel, which is where Samsung places it on some top-load and older models.

How to fix Samsung nD yourself

  1. 1 If you just ran a hot cycle such as Sanitize, Samsung says to wait about an hour for the water to cool. Unplug the washer before touching the filter or the hose.
  2. 2 Check that the washer is level, and don't remove the screw on the back that holds the drain hose.
  3. 3 Check the drain hose: 6 to 8 inches into the standpipe, secured so it can't slip further in, not sealed airtight, not kinked, and no extension kit. The standpipe height must be inside the range in your model's installation manual (18 to 96 inches on the WF42H5500 front-loader, for example).
  4. 4 On front-loaders, lay a towel and a shallow pan down, open the debris filter slowly and rinse it. Top-loaders have no owner filter.
  5. 5 Plug the washer back in and run a Spin or Drain cycle. It should drain at the start; if it doesn't, request service.

Frequently asked questions

  • What does the Samsung nD error code mean?

    Samsung's nD is a drain error: the washer could not drain the water. Depending on the model, Samsung shows the same error as 5E, 5C, SE or SC. Samsung says incorrect drain hose installation is the most common reason for drain issues and that service is rarely required.

  • What causes the Samsung nD error?

    Drain hose installed incorrectly: pushed too far into the standpipe, sealed airtight, or outside the height range for your model; Kinked, bent or damaged drain hose; Clogged debris filter (front-loaders only; top-loaders don't have one); A washer that isn't level; A drain pump fault, which needs a technician's diagnosis.

  • How can I troubleshoot Samsung nD myself?

    If you just ran a hot cycle such as Sanitize, Samsung says to wait about an hour for the water to cool. Unplug the washer before touching the filter or the hose. Check that the washer is level, and don't remove the screw on the back that holds the drain hose. Check the drain hose: 6 to 8 inches into the standpipe, secured so it can't slip further in, not sealed airtight, not kinked, and no extension kit. The standpipe height must be inside the range in your model's installation manual (18 to 96 inches on the WF42H5500 front-loader, for example). On front-loaders, lay a towel and a shallow pan down, open the debris filter slowly and rinse it. Top-loaders have no owner filter. Plug the washer back in and run a Spin or Drain cycle. It should drain at the start; if it doesn't, request service.

  • When should I call a professional for Samsung nD?

    If the washer still doesn't drain at the start of a test cycle with the hose and filter checked. The drain pump and its wiring then need a technician's diagnosis.